元器件交易网www.cecb2b.comMOTOROLASEMICONDUCTOR TECHNICAL DATAQuad Line ReceiverThe MC10115 is a quad differential amplifier designed for use in sensingdifferential signals over long lines. The base bias supply (VBB) is made availableat pin 9 to make the device useful as a Schmitt trigger, or in other applicationswhere a stable reference voltage is necessary.Active current sources provide the MC10115 with excellent common modenoise rejection. If any amplifier in a package is not used, one input of thatamplifier must be connected to VBB (pin 9) to prevent upsetting the currentsource bias network.MC10115L SUFFIXCERAMIC PACKAGECASE 620–10P SUFFIXPLASTIC PACKAGECASE 648–08FN SUFFIXPLCCCASE 775–02PD= 110 mW typ/pkg (No Load)tpd= 2.0 ns typtr, tf= 2.0 ns typ (20%–80%)LOGIC DIAGRAM457610111312VBB*VCC1= PIN 1VCC2= PIN 16 VEE= PIN 8*VBB to be used to supply bias to the MC10115 only and bypassed (when used)with 0.01 µF to 0.1 µF capacitor to ground (0 V). VBB can source < 1.0 mA.When the input pin with the bubble goes positive, the output goes negative.23VCC114159AOUTBOUTAINAINBINBINVEEDIPPIN ASSIGNMENT12345678161514131211109VCC2DOUTCOUTDINDINCINCINVBBPin assignment is for Dual–in–Line Package.For PLCC pin assignment, see the Pin ConversionTables on page 6–11 of the Motorola MECL DataBook (DL122/D).3/93© Motorola, Inc. 19963–59REV 5元器件交易网www.cecb2b.comMC10115ELECTRICAL CHARACTERISTICSTest LimitsCharacteristicPower Supply Drain CurrentInput CurrentSymbolIEIinHICBOOutput VoltageOutput VoltageThreshold VoltageThreshold VoltageReference VoltageSwitching TimesPropagation DelayRise TimeFall Time(20 to 80%)(20 to 80%)(50Ω Load)t4–2+t4+2–t2+t2–22221.01.01.11.13.13.13.63.61.01.01.11.12.92.93.33.31.01.01.11.13.33.33.73.7Logic 1Logic 0Logic 1Logic 0VOHVOLVOHAVOLAVBBPiPinUnderTest844222291.420–1.060–1.890–1.080–1.6551.280–1.350–30°CMinMax291501.5–0.890–1.675–0.960–1.850–0.980–1.630–1.2301.295Min+25°CTypMax26951.0–0.810–1.650–0.890–1.825–0.910–1.595–1.150Min+85°CMax29951.0–0.700–1.615UnitmAdcµAdcµAdcVdcVdcVdcVdcVdcnsELECTRICAL CHARACTERISTICS (continued)TEST VOLTAGE VALUES (Volts)@ Test TemperatureVIHmax–30°C+25°C+85°CPinUnderTest84422229Pulse Int4–2+t4+2–(20 to 80%)(20 to 80%)t2+222444Pulse Out2225,6,11,125,6,11,125,6,11,127,10,1344–0.890–0.810–0.700VILmin–1.890–1.850–1.825VIHAmin–1.205–1.105–1.035VILAmax–1.500–1.475–1.440VBBFromPin9VEE–5.2–5.2–5.2(VCC)Gnd1, 161, 161, 161, 161, 161, 161, 161, 16+2.0 V1, 161, 161, 16TEST VOLTAGE APPLIED TO PINS LISTED BELOWVIHmaxVILmin4,7,10,137,10,137,10,1347,10,137,10,137,10,1344VIHAminVILAmaxVBB5,6,11,125,6,11,125,6,11,125,6,11,125,6,11,125,6,11,125,6,11,125,6,11,12VEE888,488888–3.2 V888CharacteristicPower Supply Drain CurrentInput CurrentSymbolIEIinHICBOLogic 1Logic 0Logic 1Logic 0VOHVOLVOHAVOLAVBBOutput VoltageOutput VoltageThreshold VoltageThreshold VoltageReference VoltageSwitching TimesPropagation DelayRise TimeFall Time(50Ω Load)t2–2425,6,11,1281, 16Each MECL 10,000 series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has beenestablished. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained.Outputs are terminated through a 50-ohm resistor to –2.0 volts. Test procedures are shown for only one gate. The other gates are tested in thesame manner.MOTOROLA3–60MECL DataDL122 — Rev 6元器件交易网www.cecb2b.comMC10115OUTLINE DIMENSIONSFN SUFFIXPLASTIC PLCC PACKAGECASE 775–02ISSUE CB–N–Y BRKD–L––M–WDVZ0.007 (0.180) MTL–MUSNSS0.007 (0.180) MTL–MNS201XVIEW D–DG10.010 (0.250) STL–MSNSAZR0.007 (0.180) MTL–M0.007 (0.180) MTL–MSNNSSSH0.007 (0.180) MTL–MSNSCE0.004 (0.100)GG10.010 (0.250) STL–MJ–T–SEATINGPLANEK1KFVIEW S0.007 (0.180) MTL–MSVIEW SSNSNSNOTES:1.DATUMS –L–, –M–, AND –N– DETERMINEDWHERE TOP OF LEAD SHOULDER EXITS PLASTICBODY AT MOLD PARTING LINE.2.DIMENSION G1, TRUE POSITION TO BEMEASURED AT DATUM –T–, SEATING PLANE.3.DIMENSIONS R AND U DO NOT INCLUDE MOLDFLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250)PER SIDE.4.DIMENSIONING AND TOLERANCING PER ANSIY14.5M, 1982.5.CONTROLLING DIMENSION: INCH.6.THE PACKAGE TOP MAY BE SMALLER THAN THEPACKAGE BOTTOM BY UP TO 0.012 (0.300).DIMENSIONS R AND U ARE DETERMINED AT THEOUTERMOST EXTREMES OF THE PLASTIC BODYEXCLUSIVE OF MOLD FLASH, TIE BAR BURRS,GATE BURRS AND INTERLEAD FLASH, BUTINCLUDING ANY MISMATCH BETWEEN THE TOPAND BOTTOM OF THE PLASTIC BODY.7.DIMENSION H DOES NOT INCLUDE DAMBARPROTRUSION OR INTRUSION. THE DAMBARPROTRUSION(S) SHALL NOT CAUSE THE HDIMENSION TO BE GREATER THAN 0.037 (0.940).THE DAMBAR INTRUSION(S) SHALL NOT CAUSETHE H DIMENSION TO BE SMALLER THAN 0.025(0.635).DIMABCEFGHJKRUVWXYZG1K1INCHESMILLIMETERSMINMAXMINMAX0.3850.3959.7810.030.3850.3959.7810.030.1650.1804.204.570.0900.1102.292.790.0130.0190.330.480.050 BSC1.27 BSC0.0260.0320.660.810.020–––0.51–––0.025–––0.64–––0.3500.3568.899.040.3500.3568.899.040.0420.0481.071.210.0420.0481.071.210.0420.0561.071.42–––0.020–––0.502 10 2 10 ____0.3100.3307.888.380.040–––1.02–––MECL DataDL122 — Rev 63–61MOTOROLA元器件交易网www.cecb2b.comMC10115OUTLINE DIMENSIONSL SUFFIXCERAMIC DIP PACKAGECASE 620–10ISSUE V9–A–16–B–18CLNOTES:1.DIMENSIONING AND TOLERANCING PERANSI Y14.5M, 1982.2.CONTROLLING DIMENSION: INCH.3.DIMENSION L TO CENTER OF LEAD WHENFORMED PARALLEL.4.DIMENSION F MAY NARROW TO 0.76 (0.030)WHERE THE LEAD ENTERS THE CERAMICBODY.DIMABCDEFGHKLMNINCHESMILLIMETERSMINMAXMINMAX0.7500.78519.0519.930.2400.2956.107.49–––0.200–––5.080.0150.0200.390.500.050 BSC1.27 BSC0.0550.0651.401.650.100 BSC2.54 BSC0.0080.0150.210.380.1250.1703.184.310.300 BSC7.62 BSC0 15 0 15 ____0.0200.0400.511.01–T–SEATINGPLANENEFDG16 PLKMJ16 PL0.25 (0.010)MMTBS0.25 (0.010)TAS–A–169P SUFFIXPLASTIC DIP PACKAGECASE 648–08ISSUE RB18NOTES:1.DIMENSIONING AND TOLERANCING PER ANSIY14.5M, 1982.2.CONTROLLING DIMENSION: INCH.3.DIMENSION L TO CENTER OF LEADS WHENFORMED PARALLEL.4.DIMENSION B DOES NOT INCLUDE MOLD FLASH.5.ROUNDED CORNERS OPTIONAL.DIMABCDFGHJKLMSINCHESMILLIMETERSMINMAXMINMAX0.7400.77018.8019.550.2500.2706.356.850.1450.1753.694.440.0150.0210.390.530.0400.701.021.770.100 BSC2.54 BSC0.050 BSC1.27 BSC0.0080.0150.210.380.1100.1302.803.300.2950.3057.507.740 10 0 10 ____0.0200.0400.511.01FSCL–T–HKGD16 PLSEATINGPLANEJTAMM0.25 (0.010)MMotorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regardingthe suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, andspecifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motoroladata sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights ofothers. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or otherapplications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injuryor death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorolaand its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney feesarising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges thatMotorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an EqualOpportunity/Affirmative Action Employer.How to reach us:USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454MFAX: RMFAX0@email.sps.mot.com – TOUCHTONE 602–244–6609INTERNET: http://Design–NET.comJAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298MOTOROLA◊3–62*MC10115/D*MC10115/DMECL DataDL122 — Rev 6